热线电话
0531-69951198
网站开云app下载
关于精拓
产品展厅
新闻中心
原理选型
客户案例
在线留言
联系我们
网站公告:

新闻中心

济南精拓流体设备有限公司

电话:0531-69951198

邮箱:jingtuolt@163.com

传真:0531-69951198

地址:济南市历城区祝甸北路2号院

网址:http://www.sdjingtuo.com

企业动态

当前位置:开云app下载 - 新闻中心 - 企业动态初次使用者如何调节气液增

初次使用者如何调节气液增压泵

发布时间:2022-10-14 13:48:23   发布人:http://www.sdjingtuo.com
如何调节气液增压泵?对使用过气液增压泵的用户来说是没什么的,但是对初次使用者来说操作不当会导致被检测件因为压力过高而损坏,下面小编就给大家总结下初次使用要注意那些细节。
How to adjust the gas-liquid booster pump? It is nothing for users who have used the gas-liquid booster pump, but for first-time users, improper operation will lead to damage of the tested parts due to excessive pressure. The following brief section summarizes the details that should be paid attention to when using the pump for the first time.
1.首先初次使用要确保气液增压泵是按厂方要求连接,不要用低于气液增压泵更高使用压力的配件如:高压管路,卡套接头,高压开关等。
1. First of all, make sure that the gas-liquid booster pump is connected according to the manufacturer's requirements. Do not use accessories with a higher working pressure than the gas-liquid booster pump, such as: high-pressure pipeline, ferrule connector, high-pressure switch, etc.
气液增压泵
2.在使用合适的配件下按使用要求以此连接好,再检查是否有泄露(液压和气压不同稍微泄露会导致压力浮动较大,再次增压会形成脉冲对产品精细部件有影响)。
2. Use appropriate accessories to connect according to the use requirements, and then check whether there is leakage (slight leakage due to different hydraulic and air pressure will lead to large pressure fluctuation, and re pressurization will cause pulse to affect the fine parts of the product).
3.在满足上述条件后再检查驱动气源是否满足使用要求,被增压的介质是否纯洁和连接好
3. After meeting the above conditions, check whether the driving air source meets the operating requirements, and whether the pressurized medium is pure and well connected
4.完成以上步奏后打开驱动气源,调节二连体上的压力调节阀,从压力0往高处调节至所使用压力,等气液增压泵高压出口有液体排出时证明增压缸内空气完全排出,切断驱动气源,连接被检测件再打开气源。如果检测在长时间内承压能力就不用切断气源,检测密封性2种办法:1,切断气源看压降2,保持气源畅通看渗漏。
4. After completing the above steps, open the driving air source, adjust the pressure regulating valve on the duplex, and adjust the pressure from 0 to the used pressure. When liquid is discharged from the high-pressure outlet of the gas-liquid booster pump, it is proved that the air in the booster cylinder is completely discharged. Cut off the driving air source, connect the tested part and then open the air source. If the pressure bearing capacity is tested for a long time, it is unnecessary to cut off the air source. There are two methods for testing the sealing: 1. Cut off the air source to see the pressure drop 2. Keep the air source unblocked to see the leakage.
今天关于气液增压泵的知识就介绍到这了,您还有什么不了解的请访问我们网站http://www.sdjingtuo.com吧,为您提供开云app下载相关的资讯信息!
That's all for today's knowledge about gas-liquid booster pump. Please visit our website if you have any questions http://www.sdjingtuo.com Let's provide you with more relevant information!
新闻推荐:

13188935873