热线电话
0531-69951198
网站开云app下载
关于精拓
产品展厅
新闻中心
原理选型
客户案例
在线留言
联系我们
网站公告:

新闻中心

济南精拓流体设备有限公司

电话:0531-69951198

邮箱:jingtuolt@163.com

传真:0531-69951198

地址:济南市历城区祝甸北路2号院

网址:http://www.sdjingtuo.com

业内资讯

当前位置:开云app下载 - 新闻中心 - 业内资讯气体增压泵使用注意事项标

气体增压泵使用注意事项标准

发布时间:2023-05-04 11:18:03   发布人:http://www.sdjingtuo.com
使用方要准备好被增压的气体和管路,驱动气体和管路,高压气体的出口管路,按增压泵出厂时所带的说明先固定好增压泵,按照增压泵的各个进出口接头尺寸,连接好管路;检查是否耐压足够,接头是否有泄露等,检查完好后就可以进行增压测试了。
The user should prepare the pressurized gas and pipeline, the driving gas and pipeline, and the outlet pipeline of high-pressure gas. Fix the booster pump according to the instructions provided at the factory, and connect the pipeline according to the size of each inlet and outlet joint of the booster pump; Check if the pressure resistance is sufficient, and if there are any leaks in the joints. After the inspection is complete, the pressurization test can be carried out.
气源方面:气体增压泵的驱动气源压力范围一般是在1.8-8bar,不建议它的驱动气源超过10bar,如果驱动气源过高,那么很大程度上会对泵体造成损伤,更有甚者会对操作人员造成伤害。
气体增压泵
In terms of gas source: The driving gas source pressure range of gas booster pumps is generally 1.8-8bar, and it is not recommended to exceed 10bar. If the driving gas source is too high, it will greatly damage the pump body, and even cause harm to operators.
气体增压泵选型方面:客户要根据自身需求的压力选择对应的增压比,按照客户自己的压力需求,突出气源压力、进气压力、输出压力需求、流量是多少,这样技术人员才能更准确的帮您选型。
In terms of gas booster pump selection: Customers should choose the corresponding boost ratio based on their own pressure needs, with a focus on highlighting the gas source pressure, intake pressure, output pressure demand, and flow rate according to their own pressure needs, so that technical personnel can more accurately help you select the type.
对现场使用环境方面:现场使用环境一定要干净,不能有太大的粉尘颗粒,驱动气源及被增压介质水分不要含量太多,否则会大大降低泵的使用的寿命。
In terms of on-site usage environment: The on-site usage environment must be clean and free of large dust particles. The driving air source and pressurized medium should not have too much moisture content, otherwise it will greatly reduce the service life of the pump.
对管路的要求:客户现场使用的时候一定要检测高压输出管道的密封严实性,采用的管道、阀门、压力表一定要大于气体增压泵输出的额定压力,限度的保证人员的操作安全。
Requirements for pipelines: When customers use them on site, they must check the sealing tightness of the high-pressure output pipeline. The pipelines, valves, and pressure gauges used must be greater than the rated pressure output by the gas booster pump to ensure the maximum operational safety of personnel.
对压力容器的要求:各部分承压件,特别是压力容器,一定要具有压力安全容器厂家生产的压力安全容器检查报告。
Requirements for pressure vessels: All pressure parts, especially pressure vessels, must have a pressure safety vessel inspection report produced by the pressure safety vessel manufacturer.
本文由气体增压泵进行编写,想要了解开云app下载的产品及更详细的精彩内容,请关注我们的网站:http://www.sdjingtuo.com我们将为您呈现开云app下载的内容。
This article is written by a gas booster pump. For more products and detailed exciting content, please follow our website: http://www.sdjingtuo.com We will present more content for you.
新闻推荐:

13188935873